...
The infrared sensors are the sensors that detect/measure infrared radiation or change in the radiation from outer source source or inbuilt source.
There are two types of infrared sensor based on its function:
Also sensors that uses the property of infrared radiations to detect the changes in surrounding are termed as infrared sensors.
A general working method of infrared sensors is as follows:
...
The working method of most infrared sensor is as follows.
Detection System
The detector performance is based on to following parameters:
...
Noise Equivalent Point(NEP): Noise is caused by the background radiation and it affects the signal output. NEP is the amount of incident radiation when the signal to noise ratio is 1.
Physics behind infrared sensors:
Plank’s radiation law-
The body which has temperature greater than 0 K radiates. Infrared cannot be seen through normal eyes. It describes the electromagnetic radiation emitted by black body in thermal equilibrium. Plank law can be expressed
h= 6.625×10-27 erg-sec (plank Constant)
k=1.38×10-16 erg/K (Boltzmann Constant)
c= 3×1010 cm/sec (Speed of light)
Stefan-Boltzmann Law
The thermal energy radiated by a blackbody radiator per second per unit area is proportional to the fourth power of the absolute temperature and is given by
Stefan-Boltzmann law
Wien’s Displacement law- The radiated energy is different in different temperature it increases with increase in temperature.
For the blackbody radiation the law is
For other bodies beside blackbodies the relation is given as emissivity (E)
Types of Infra-Red Sensors
Types of Infra-Red Sensors
-There are two types of infrared sensor based on its function:
- Thermal Infrared sensor:
- Quantum infrared sensor
-These are the types of infrared sensors based on the working mechanism:
- Active Infrared Sensors
- Passive Infrared sensors
ACTIVE INFRARED SENSORS
Active infrared sensors are the types of infrared sensor that emit infrared radiation which is later received by the receiver. The IR is emitted by a IR Light Emitting Diode (LED) and received by photodiode, phototransistor or photoelectric cells. During the process of detection, the radiation is altered, between process of emission and receiving, by object of interest. The alteration of radiation causes change in received radiation in the receiver. This property is used to generate desired output with help of associated electronic circuit.
There are two types of Active infrared sensors
Break beam sensors
These types of Active IR sensor have emitter and receiver placed in such a way that the IR emitted by the emitter falls directly in to the receiver. During the operation, IR beam is emitted continuously towards the receiver. The flow of IR can be interrupted by placing an object between the emitter and receiver. If the IR is transmitted but altered then receiver generates output based on the change in radiation. Similarly if the radiation is completely blocked the receiver can detect it and provide the desired output. For example: let’s consider a Break beam sensor and a conveyer belt as shown in figure. When an opaque object interrupts the IR flow the receiver doesn’t receive any signal thus the conveyer belt stops.
...
Furthermore advanced use of these types of sensors can be to acquire different shape and surface profile of objects.
Reflectance sensors
These types of sensors use reflective property of IR. The emitter emits an IR beam which is reflected by the object. The reflected IR is the detected by the receiver. The object causes change in the property of the reflected IR or the amount of IR received by the receiver varies. The degree of change is dependent on the reflectance of the object. Thus detecting the change in amount of received IR helps in figuring out the properties of object such as surface geography and reflectance.
...
Figure 2 Reflectance sensor
Passive Infrared Sensor
Passive infrared sensors detect the infrared radiations from outer source.When an object is in a field of view of a sensor it provides a reading based on a thermal input.It dose not generate any infrared.There are different kind of Passive infrared sensor.
...
- SECURITY
- Lighting appliances
- Household or other appliances
Thermal infrared sensors
Thermal infrared sensors which are also called radiation detectors undergo a change in temperature due to absorption of infrared radiation and convert this temperature change into an electric output signal. Their working principle varies compared to semiconductor based photon or quantum sensors which works on principle that due to different photoelectric effects the photons of the radiation generate charge carriers. For the sensors which work on photoelectric effects, to detect the low-energy infrared radiation, sensors have to be cooled below ambient temperature. In contrary to this, thermal infrared sensors can be operated at ambient temperature. The radiation noise that limits temperature resolution in thermal sensors has a √T dependence meaning that the cooling doesn't consequently improve detection rate. Hence they are more suitable for small, light and portable applications.
Working Principles:
Thermal radiation sensors convert radiant flux ᶲs into an electric signal (Voltage VS or Current IS). Figure represents the measuring chain of radiation sensors. Even though there are various operating principles the basic structure of all the thermal IR are identical. The incident IR radiant flux is absorbed by a thermally isolated detector element (pixel) and it is converted into heat. The temperature of the pixel is directly proportional to the power of the absorbed IR radiation. This makes the responsivity of thermal sensors independent of wavelength. However, in many scenarios there is a wavelength dependence of responsivity due to absorption characteristics of the pixel. If required IR radiation can be temporarily modulated with a chopper. The conversion of the pixel temperature into an electrical signal depends on the sensor type.
Figure: Measuring chain for determining infrared sensors.
IR sensors consist of a thin well isolated chip usually called as detector. The temperature of the detector depends on the absorbed radiant flux ᶲA and the radiant flux ᶲS emitted by the detector element. The figure below illustrates the radiation exchange at detector element, object and detector surroundings. The possible heat flow between detector element, object and detector surroundings due to the thermal conduction is neglected.
...
References
- Hamamtsu Infrared detectors/technical information
- http://www.thesis.bilkent.edu.tr/0003853.pdf
- http://www.glolab.com/pirparts/infrared.html
- http://www.sbf1.sbfisica.org.br/procs/2006/pdfs%20optics/Interferometry,%20Holography%20and%20Applied%20Optics/604%20-2.pdf
- http://www.st.com/st-web-ui/static/active/en/resource/technical/document/application_note/DM00096551.pdf
- http://www.hitechnic.com/cgi-bin/commerce.cgi?preadd=action&key=NIS1070
- http://www.cypress.com/?docID=3317
...